DeWalt D25414 Manuel d'instructions télécharger pdf (Page 6)

WARNING: We recommend the use of a residual current device with a residual

current rating of 30mA or less.

WARNING: ALWAYS wear approved protective safety equipment complying with

the following standards:

• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;

• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;

• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes,

or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use AS/NZS1716 approved

respiratory protection appropriate for the dust exposure. Direct particles away from

face and body.

WARNING: Always wear proper personal hearing protection that conforms to

AS/NZS1270 during use. Under some conditions and duration of use, noise from this

product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V ......................volts A .........................amperes

Hz ....................hertz W ........................watts

• Hold power tools by insulated gripping surfaces when performing an

operation where the cutting accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may make exposed metal parts

of the power tool “live” and could give the opeartor an electric shock.

• Use clamps or other practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body is unstable and

may lead to loss of control.

• Wear safety goggles or other eye protection. Hammering operations cause

chips to fly. Flying particles can cause permanent eye damage. Wear a dust

mask or respirator for applications that generate dust. Ear protection may be

required for most applications.

• Keep a firm grip on the tool at all times. Do not attempt to operate this tool

without holding it with both hands. Operating this tool with one hand will result

in loss of control. Breaking through or encountering hard materials such as re-bar

may be hazardous as well.

• Do not operate this tool for long periods of time. Vibration caused by hammer

action may be harmful to your hands and arms. Use gloves to provide extra

cushion and limit exposure by taking frequent rest periods.

• Do not recondition bits yourself. Chisel reconditioning should be done by an

authorized specialist. Improperly reconditioned chisels could cause injury.

• Wear gloves when operating tool or changing bits. Accessible metal parts on

the tool and bits may get extremely hot during operation. Small bits of broken

material may damage bare hands.

• Never lay the tool down until the bit has come to a complete stop. Moving bits

could cause injury.

• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal

or material chips could dislodge and cause injury.

• Keep the power cord away from the rotating bit. Do not wrap the cord around

any part of your body. An electric cord wrapped around a spinning bit may

cause personal injury and loss of control.

• Do not overheat the bit (discoloration) while grinding a new edge. Badly worn

chisels require reforging. Do not reharden and temper the chisel.

• Air vents often cover moving parts and should be avoided. Loose clothes,

jewellery or long hair can be caught in moving parts.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

DeWalt D25414 Manuel d'instructions Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Marteaux rotatifs DeWalt D25414