DeWalt DCG412 Manuel d'instructions Page 18
- Page / 85
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Alwayslockthetriggerswitchwhencarryingorstoringthetoolto
eliminateunintentionalstarting.
FIG.8 Ii_
UNLOCKED
B
LOCKED
To unlock the trigger switch, press the lock-off button. When the
lock-off button is depressed to the unlock icon, the unit is unlocked.
The lock-off button is colored red to indicate when the switch is in its
unlocked position.
Pull the trigger switch (A) to turn the motor ON. Releasing the trigger
switch turns the motor OFF.
NOTE: This tool has no provision to lock the switch in the ON position,
and should never be locked ON by any other means.
AWARNING: Hold the side handle and body of the tool firmly to
maintain control of the tool at start up and during use and until the
wheel or accessory stops rotating. Make sure the wheel has come to
a complete stop before laying the tool down.
_,WARNING: Allow the tool to reach full speed before touching
tool to the work surface. Lift the tool from the work surface before
turning the tool off.
SPINDLE LOCK BUTTON (FIG. 2)
The spindle lock button (C)is provided to prevent the spindle from
rotating when installing or removing wheels. Operate the spindle lock
button only when the tool is turned off, the battery is removed, and
the wheel has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do not engage
the spindle lock button while the tool is operating. Damage to
the tool will result and attached accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button (C)and rotate the
spindle until you are unable to rotate the spindle further.
Mounting and Using Depressed Center
Grinding Wheels and Sanding Flap Discs
NOTE: The Type 27 guard MUST be used and is available at extra
cost from your local dealer or authorized service center.
MOUNTING AND REMOVING HUBBED WHEELS
_WARNING: To reduce the risk of serious personal injury,
turn tool off and remove the battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
Hubbed wheels install directly on the 5/8"-11 threaded spindle.
1. Thread the wheel on the spindle by hand.
2. Depress the spindle lock button and use a wrench to tighten the
hub of the wheel.
3. Reverse the above procedure to remove the wheel.
NOTICE: Failure to properly seat the wheel before turning the tool on
may result in damage to the tool or the wheel
MOUNTING NON-HUBBED WHEELS
_WARNING: To reduce the risk of serious personal injury,
turn tool off and remove the battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
17
- INSTRUCTION MANUAL 1
- GUIDE D'UTILISATION 1
- MANUAL DE INSTRUCCIONES 1
- FOR FUTURE REFERENCE 2
- SAFETY INSTRUCTIONS FOR 4
- ALL OPERATIONS 4
- Brushing Operations 7
- Additional Safety Information 7
- READ ALL INSTRUCTIONS 8
- Battery Chargers 9
- Chargers 11
- Indicator Light Operation 11
- Charge Indicators 11
- Important Charging Notes 12
- Storage Recommendations 12
- Mounting Guard 14
- Wire Wheels 15
- Sanding Discs 16
- 4-1/2" (114.3 mm) 16
- Sanding Flap Discs 16
- Cutting Wheels 16
- OPERATION 17
- FIG.8 Ii_ 18
- Clamp nut Clamp nut 19
- Backing flange Backing flange 19
- Mounting and Using Cutting 22
- Cleaning 24
- Lubrication 24
- Purchasing Accessories 24
- Three Year Limited Warranty 25
- (sansfi/) 26
- CONSIGNES DE SECURITE POUR 28
- TOUTES LES OPERATIONS 28
- Avertissements de s_curit_ 31
- LIRE TOUTES LES CONSIGNES 34
- Le sceau SRPRC Mc 35
- Sup_rieur Inf_rieur 36
- Procedure de charge 37
- Fonctionnement du voyant 37
- Voyants de charge 37
- Recommandations de stockage 39
- CONSERVER CES CONSIGNES POUR 39
- UTILISATION ULTERIEURE 39
- COMPOSANTS (FIG. 2, 9) 39
- ASSEMBLAGE ET REGLAGES 40
- (Fig. 2) 40
- Accessoires 40
- Brosses m_talliques 42
- Disque de coupe 43
- FONCTIONNEMENT 44
- Interrupteur 44
- FIG.8 ,_ DI_VERROUILLI_ 45
- (I/4 PO) (I/8 PO) 46
- ENTRETIEN 52
- Nettoyage 52
- Graissage 52
- R_parations 52
- Achat d'accessoires 53
- Garantie limit_e de trois ans 53
- / 4 t/_ (l_Sm.}HEAVYOUT¥ 54
- To_EDUCET.ERISKOFI_JU_V,USE_ 54
- TODAS LAS OPERACIONES 58
- LEA TODAS LAS INSTRUCCIONES 63
- E1 sello RBRC TM 64
- Cargadores 66
- Indicadores de carga 66
- Componentes (Fig. 2, 9) 68
- ENSAMBLADO Y AJUSTES 69
- Accesorios 69
- Protector de montaje 69
- FUNCIONAMIENTO 70
- Interruptor 71
- Discos de esmerilar 72
- Discos de 73
- Discos para lijar 73
- FIG.8 All DESBLOQUEADO 74
- (114") (118") 75
- Brida de respaldo 75
- (Tipo 1) 79
- MANTENIMIENTO 81
- Limpieza 81
- Lubricaci6n 81
- Reparaciones 81
- P61iza de Garantia 82
Produits connexes et manuels pour Outils électriques DeWalt DCG412
(20 pages)
(38 pages)
(23 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.186 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels