DeWalt D25601 Manuel de service télécharger pdf (Page 10)

E N G L I S H

Electronic Speed and Impact Control

(ﬁg. 1, 3)

D25601, D25602, D25603

The electronic speed and impact control (g) offers

the following advantages:

– use of smaller accessories without risk of

breakage;

– minimised break-out when chiselling or drilling in

soft or brittle materials;

– optimal tool control for precise chiselling.

Torque Limiting Clutch

The torque limiting clutch reduces the maximum

torque reaction transmitted to the operator in case of

jamming of a drill bit. This feature also prevents the

gearing and electric motor from stalling. The torque

limiting clutch has been factory-set and cannot be

adjusted.

Complete Torque Control (ﬁg. 3)

D25602, D25603

NOTICE: Always turn the tool off before

changing torque control settings

damage to tool may result.

The Complete Torque Control (CTC) feature of this

tool is designed to provide additional control with a

two-stage clutch mechanism. Refer to Setting the

Torque Control Switch for more information.

Adaptive Drill Contol (ADC)

D25603 (FIG. 3)

The D25603 is equipped with an adaptive drill

control. This feature senses the motion of tool and

reduces the motor torque to a manageable level if

necessary. The red indicator LED (r) will illuminate to

indicate status.

NOTE: If tool power is insufﬁcient for normal drilling

and the red LED indicator does not ﬂash, take the

tool to an authorized D

EWALT repair center.

Service Indicator LEDs (ﬁg. 3)

D25601, D25602, D25603

The yellow brushwear indicator LED (s) lights up

when the carbon brushes are nearly wo

rn out to

indicate that the tool needs servicing within the next

8 hours of use.

D25601, D25602, D25603

The red service indicator LED (r) lights up if the

lock-on button (b) is used in any mode except the

chipping mode. In all models with the adaptive drill

control (ADC), the red indicator LED (r) lights up

if the ADC is engaged. The red indicator starts to

ﬂash if there is a fault with the tool or the brushes

have completely worn out (refer to Brushes under

Maintenance ).

Fully Vibration-dampened Main

Handle (ﬁg. 1)

D25601, D25602, D25603

The dampers in the side handle (c) absorb the

vibrations transmitted to the user. This improves user

comfort during the operation.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

EWALT service organisation.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of this tool

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

WARNING: Tool bits may be hot and

gloves should be worn when changing

or removing them to avoid personal

injury.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 40 41

Commentaires sur ces manuels

Pas de commentaire

DeWalt D25601 Manuel de service Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Marteaux rotatifs DeWalt D25601