DeWalt DWS778 Manuel de service télécharger pdf (Page 11)

ENGLISH

i. Sliding fence lock lever (fig. 11)

j. Fixed table

k. Kerf plate

l. Mitre arm

m. Mitre latch

n. Rotating table/mitre arm

o. Mitre scale

p. Mitre scale screws (fig. 12)

q. Sliding fence

r. Dust extraction nozzle

s. Traverse lock

t. Bevel clamp handle

u. Bevel scale

v. Bench mounting holes

w. Lock-down button

x. Traverse bars

y. Saw head

z. Hex keys

aa. Cable clamp

bb. Padlock hole

cc. Override button

dd. Carrying indentations (left and right)

ee. Inner flange (fig. 7)

ff. Material clamp

gg. XPS

Worklight on/off switch

hh. XPS

Worklight

ii. Twist lock connector (DWV9000, optional accessory)

INTENDED USE

Your D

EWALT Cross-Cut Mitre Saw has been designed for professional

cutting of wood, wood products, plastics and aluminium. It performs

the sawing operations of cross-cutting, bevelling and mitring easily,

accurately and safely.

When assembled with a suitable saw blade, this machine is designed

for cutting aluminium profiles up to a maximum thickness of 4.0 mm.

NEVER cut magnesium.

This unit is designed for use with a nominal blade diameter 250 mm

carbide tip blade.

DO NOT use under wet conditions or in presence of flammable liquids

or gases.

These miter saws are professional power tools.

DO NOT let children come into contact with the tool. Supervision is

required when inexperienced operators use this tool.

WARNING! Do not use the machine for purposes other

than intended.

• This product is not intended for use by persons (including children)

suffering from diminished physical, sensory or mental abilities; lack

of experience, knowledge or skills unless they are supervised by

a person responsible for their safety. Children should never be left

alone with this product.

Electrical Safety

The electric motor has been designed for one voltage only. Always

check that the power supply corresponds to the voltage on the rating

plate.

Your tool is double insulated in accordance with EN 61029;

therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe

isolating transformer with an earth screen between the

primary and secondary winding.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the DEWALT service organisation.

In case of cord replacement, the tool must only be repaired by an

authorized service agent or by qualified electrician.

The following cords are mandatory:

DWS778: H05RN-F, 2x1.0 mm²

DWS778 LX: H05RR-F, 2x1.5 mm²

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth

terminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Fitting a Mains Plug to 115 V Units

(U.K. and Ireland Only)

• The plug fitted should be comply with BS EN 60309 (BS4343),

16 Amps, earthing contact position 4h.

WARNING: Always ensure that the cable clamp (aa) is

correctly and securely fitted to the sheath of the cable.

Using an Extension Cable

If an extension cable is required, use an approved 3–core extension

cable suitable for the power input of this tool (see Technical Data).The

minimum conductor size is 1.5 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable completely.

ASSEMBLY

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting

or changing set-ups or when making repairs. Be sure

the trigger switch is in the OFF position. An accidental start-

up can cause injury.

Unpacking

The motor and guards are already assembled onto the base.

Bench Mounting (ﬁ g. 2)

1. Holes (v) are provided in all four feet to facilitate bench mounting.

Two different sized holes are provided to accommodate different

sizes of bolts. Use either hole; it is not necessary to use both.

Always mount your saw firmly to prevent movement. To enhance

the portability, the tool can be mounted to a piece of 12.5 mm or

thicker plywood which can then be clamped to your work support

or moved to other job sites and reclamped.

2. When mounting your saw to a piece of plywood, make sure that

the mounting screws do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When clamping

the saw to any work surface, clamp only on the clamping bosses

where the mounting screw holes are located. Clamping at any

other point will interfere with the proper operation of the saw.

3. To prevent binding and inaccuracy, be sure the mounting surface is

not warped or otherwise uneven. If the saw rocks on the surface,

place a thin piece of material under one saw foot until the saw is

firm on the mounting surface.

Mounting the Saw Blade (ﬁ g. 2, 6–8)

WARNING: To reduce the risk of injury, turn unit off

and disconnect machine from power source before

installing and removing accessories, before adjusting

or changing set-ups or when making repairs. Be sure

the trigger switch is in the OFF position. An accidental

start-up can cause injury.

WARNING: The teeth of a new blade are very sharp and

can be dangerous.

WARNING: Be aware the saw blade shall be replaced in

the described way only. Only use saw blades as specified

under Technical Data; Cat.no.: DT4282 is suggested.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

DeWalt DWS778 Manuel de service Page 11

Commentaires sur ces manuels