DeWalt D25013 Manuel d'instructions Page 9
- Page / 36
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7
English
DRILL-ONLY MODE
To use drill-only mode, press mode selector button (F) and turn the
mode selector (G) so the yellow arrow points to the corresponding
symbol as shown. Use drill-only mode for wood, metal, and
plastics.
HAMMERDRILL MODE
To use hammerdrill mode, press the mode selector button (F)
and turn the mode selector (G) so the yellow arrow points to the
corresponding symbol as shown. Use this mode for masonry
drilling.
HAMMER-ONLY MODE
For light chiseling, press the mode selector button (F) and turn the
mode selector (G) so the yellow arrow points to the corresponding
symbol as shown.
NOTE: The yellow arrow on the mode selector MUST be aligned
with the one of the symbols at all times. There are no operable
positions between the positions.
SDS-plus
®
Chuck (Fig. 1)
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING: Burn Hazard. ALWAYS wear gloves when changing
bits. Accessible metal parts on the tool and bits may get extremely
hot during operation. Small bits of broken material may damage
bare hands.
WARNING: Do not attempt to tighten or loosen drill bits (or any
other accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may occur.
To insert bit, insert shank of bit about 3/4" (19 mm), no further than
7/8" (22 mm) into chuck. Push and rotate bit until it locks in place.
The bit will be securely held.
To release bit, pull the chuck sleeve (E) back and remove the bit.
OPERATION
WARNING: Always observe the safety instructions and applicable
regulations.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories.
WARNING: To reduce the risk of personal injury, ALWAYS
ensure workpiece is anchored or clamped firmly. If drilling thin
material, use a wood “back-up” block to prevent damage to the
material.
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed and
securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
Proper Hand Position (Fig. 3)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the
FIG. 3
B
C
risk of serious personal injury,
ALWAYS hold securely in
anticipation of a sudden
reaction.
Proper hand position requires
one hand on the side handle
(C), with the other hand on the
main handle (B).
- FOR FUTURE REFERENCE 3
- Rotary Hammers 4
- COMPONENTS (Fig. 1) 7
- ASSEMBLY AND ADJUSTMENTS 7
- Side Handle (Fig. 1) 7
- Trigger Switch (Fig. 1) 8
- Reversing Lever (Fig. 1) 8
- Mode Selector (Fig. 2) 8
- SDS-plus 9
- Chuck (Fig. 1) 9
- OPERATION 9
- Proper Hand Position (Fig. 3) 9
- Overload Clutch 10
- Drilling Tools 10
- Drilling (Fig. 1) 10
- Chipping and Chiselling 11
- Depth Rod (Fig. 4) 11
- MAINTENANCE 11
- Cleaning 11
- Lubrication 12
- Accessories 12
- Definiciones: Normas 13
- DESCRIPCIÓN (FIG. 1) 17
- MONTAJE Y AJUSTES 18
- Mango lateral (Fig. 1) 18
- Palanca de reversa (Fig. 1) 19
- Selector de modo (Fig. 2) 19
- FUNCIONAMIENTO 20
- Bien colocar las 20
- Embrague de sobrecarga 21
- Taladros (Fig. 1) 21
- Taladrado 21
- Cincelado 22
- Português 24
- Definições: Diretrizes de 24
- Segurança 24
- Regras Gerais de Segurança 24
- GUARDE ESTAS INSTRUÇÕES 24
- Componentes (Fig. 1) 28
- MONTAGEM E AJUSTES 29
- Empunhadura lateral (Fig. 1) 29
- Alavanca de reversão (Fig. 1) 30
- Limitador de torque 32
- Ferramentas de perfuração 32
- Perfuração (Fig. 1) 32
- Rompedor 33
- MANUTENÇÃO 34
- Lubrificação 34
- Acessórios 34
Produits connexes et manuels pour Outils électriques DeWalt D25013
(258 pages)
(204 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.675 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels