23
ENGLISH
• Loosen the side handle.
• For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
• For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
• Insert the required drill bit.
• Slacken the side handle (5).
• Fit the depth adjustment rod (6) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
Forward/Reverse-lever (fig. F)
• Push the forward/reverse-lever (3) to the LH-side
for forward (RH) rotation. See arrows on tool.
• Push the forward/reverse-lever (3) to the RH-side
for reverse (LH) rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover
immediately.
• Pull back the tool holder locking sleeve (9) and
pull the dust cover (7) off.
• Fit the new dust cover.
• Release the tool holder locking sleeve.
How to fit the Chuck Adapter & Chuck
• Unplug the tool.
• Screw the keyed chuck onto the threaded end of
the chuck adapter.
• Insert the connected chuck and adapter in the
tool as though it were a standard SDS-plus
®
bit.
• Always tighten the accessory into the keyed
chuck using all three holes.
• To remove the chuck, proceed as for removing a
standard SDS-plus
®
bit.
• Never use the keyed chuck in hammer
drilling mode.
Instructions for use
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework and
wiring.
• Apply only a gentle pressure to the tool
(approx. 2-3 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
• Do not drill or drive too deep to prevent
damage to the dust cover.
Switching ON and OFF (fig. A)
• To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed
switch determines the tool speed.
• If necessary, press the lock-on button (2) for
continuous operation and release the variable
speed switch. The lock-on button works only in
full speed, forward rotation.
• To stop the tool, release the variable speed switch.
• To stop the tool in continuous operation, press
the variable speed switch briefly and release it.
Always switch OFF the tool when work is finished
and before unplugging.
Hammer drilling (fig. A)
• Select the hammer drilling mode (4).
• Insert the appropriate SDS-plus
®
bit. For best
results use high quality carbide-tipped bits.
• Mark the spot where the hole is to be drilled.
• Press the tool against the workpiece.
• Switch the tool ON by pressing the variable speed
switch (1). The hammer mechanism should run
smoothly and the tool should not bounce. If
necessary, increase the pressure on the switch.
Rotary drilling (fig. A)
• Select the rotary drilling mode (4).
• Proceed as described for hammer drilling. Special
SDS-plus
®
adaptors with threaded sections are
available for use with standard 10 or 13 mm
chucks to enable straight shank bits to be used.
Never use standard chucks in the
hammer drilling mode.
(36 pages)
(36 pages)
(140 pages)
(36 pages)
(20 pages)
(36 pages)
(40 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels