DeWalt D28700 Manuel de service télécharger pdf (Page 32)

ENGLISH

• Replace the cutting disc (5). Make sure that the

new disc is placed onto the spacer (19) in the

correct rotational direction.

• Secure the blade with the retaining ﬂ ange (18),

the ﬂ at washer (17) and the bolt (16).

• Move the guard back down and release the

spindle lock (6).

• Adjust the cutting depth as necessary (ﬁ g. B3).

Adjusting the cutting depth ( g. B3)

The cutting depth can be adjusted to meet the wear

of the cutting disc.

• Make a dry run with the tool switched off and

check for clearance.

• If adjustment is required, proceed as follows:

• Loosen the lock nut (21) a few turns.

• Turn the depth stop bolt (12) in or out as to

achieve the required cutting depth.

• Tighten the lock nut (21).

Always adjust the depth stop to its original

position when replacing the cutting disc.

Clamping the workpiece in position

(ﬁ g. A & C1 - C4)

The tool is equipped with a material clamp (6) (ﬁ g. A).

• Pull the lever (22) toward the handle (23) (ﬁ g. C1).

• Push the clamp shaft (24) forward until the jaw

(25) is almost touching the workpiece.

• Press the lever (22) toward the jaw (25) until it

engages with the clamp shaft (24).

• Rotate the handle (23) clockwise and clamp the

workpiece securely.

• To release the workpiece, rotate the handle (23)

counterclockwise.

WARNING:

• To increase the cutting capacity, place a

spacer block (26) under the workpiece

(27). The spacer block should be slightly

narrower than the workpiece (ﬁ g. C2).

• Support long workpieces using a piece

of wood (28) (ﬁ g. C3). Do not clamp the

cut off end (27).

Quick travel feature ( g. C1)

The clamp has a quick travel feature.

• To release the clamp, rotate the handle (23) one

or two turns counterclockwise and pull the lever

(22) toward the handle (23).

Setting the clamping position ( g. C4)

The clamping position can be set to match the

cutting disc.

• Remove the fence bolts (29) using the hex key (14).

• Move the fence (8) as required.

• Re-ﬁ t the fence bolts (29) and tighten them to

lock the fence (8).

Adjusting the angle of cut (ﬁ g. D)

The tool can be used for mitre cuts up to 45°.

• Loosen the fence bolts (29) to release the fence (8).

• Set the fence (8) to the required angle. The angle

can be read on the scale (30).

• Tighten the fence bolts (29) to lock the fence (8).

Checking and adjusting the mitre scale (ﬁ g. A & D)

• Loosen the fence bolts (29) to release the fence

(8) (ﬁ g. D).

• Pull down the arm and lock it in this position by

pushing in the lock-down pin (13) (ﬁ g. A).

• Place a square (31) against the fence (8) and the

left side of the cutting disc creating a perfect 90°

(ﬁ g. D). Check that the 0° marking on the scale

(30) aligns with the marking on the table (31).

• Tighten the fence bolts (29) to lock the fence (8).

• Pull out the lock-down pin (13) and return the

arm to its upper rest position (ﬁ g. A).

Adjusting the spark deﬂ ector (ﬁ g. E)

• Loosen the screw (33).

• Set the spark deﬂ ector (11) as appropriate.

• Tighten the screw (33).

Prior to operation

• Install the appropriate cutting disc. Do not use

excessively worn discs. The maximum rotation

speed of the tool must not exceed that of the

cutting disc.

• Make sure the disc rotates in the direction of the

arrows on the accessory and the tool.

• Secure the workpiece.

• Always set the spark deﬂ ector correctly.

OPERATION

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Do not apply excessive pressure to the tool.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 127 128

Commentaires sur ces manuels

Pas de commentaire

DeWalt D28700 Manuel de service Page 32

Commentaires sur ces manuels

Produits connexes et manuels pour Scies circulaires DeWalt D28700