DeWalt DW258-XE Manuel d'instructions télécharger pdf (Page 5)

Additional Safety Instructions

• Hold tool by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a “live”

wire will make exposed metal parts of the tool “live” and shock the operator.

• Keep handles dry, clean, free from oil and grease. It is recommended to use

rubber gloves. This will enable better control

• Keep tool dry from sweat during use. Reduce risk of electric shock by preventing

perspiration or other liquids from entering the tool during use in hot/humid

conditions. Use wristbands, gloves, drying towels or cloths as necessary.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes,

or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from

face and body.

WARNING: ALWAYS wear proper personal hearing protection that conforms to

ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise

from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V ................. volts A ...............amperes

Hz ............... hertz W ..............watts

min ............. minutes

...........alternating current

.......... direct current

o ..............no load speed

..............Class I Construction .............earthing terminal

................... (grounded) .............safety alert symbol

............... Class II Construction …/min .......revolutions per minute

................... (double insulated) BPM ..........beats per minute

COMPONENTS

Switch

To start tool, depress the trigger switch, shown in

FIG. 1

Figure 1.

To stop tool, release the switch. The variable speed

trigger switch permits speed control. The farther

the trigger switch is depressed, the higher the

speed of the tool.

To lock the switch in the on position for continuous

operation, depress the trigger switch and push up

the locking button. The tool will continue to run.

To turn the tool off, from a locked on condition,

squeeze and release the trigger once. Before

using the tool (each time), be sure that the locking

button release mechanism is working freely.

WARNING: Be sure to release the locking mechanism before disconnecting the

plug from the power supply. Failure to do so will cause the tool to start immediately

the next time it is plugged in. Damage or injury could result.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

DeWalt DW258-XE Manuel d'instructions Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques DeWalt DW258-XE